Home / LoRaWAN Payload Helper

Vicki
HT Sensor
Wireless Thermostat
Flood Sensor
T-Valve
Button
Fan Coil Thermostat
Open/Close Sensor
CO2 Sensor
CO2 Display

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Recalibrate Motor

Set open window parameters

Set Child Lock

Possible values: 0 (disabled) and 1 (enabled)

Set temperature range

Force Close

Set Internal Algo Params

Set Internal Algo Params Tdiff Only

Set device operational mode

Possible values:
0 – Online manual control mode;
1 – Online automatic control mode;
2 – Online automatic control mode with external temperature reading.

Set Target Temperature

Possible value range: 5C - 30C

Set target temperature and motor position

Set Motor Position

Set Join Retry Period

Value should be in minutes

Set uplink type

Possible values: 0 (unconfirmed) and 1 (confirmed)

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Set device primary operational mode

Possible values:
0 – Vicki operates in heating mode (default for the device);
1 – Vicki operates in cooling mode;

External temperature sensor reading

Applicable to certain device online operational modes
The desired temperature in Celsius degrees. The value must be greater than 0°C

Temperature control algorithm selection

Possible values:
0 – For the device to use the "Proportional control" algorithm;
1 – For the device to use the "Equal directional control" algorithm;

Proportional algorithm parameters

Remote reset the device

Set Child Lock Behavior

Possible values:
0 – Child lock is automatically disabled when the device goes offline.
1 – Child lock remains unchanged when the device goes offline.

Set External Temperature with accuracy 0.1

Set PI's algo Proportional gain

Set PI's algo Integral gain

Set PI run period

Set PI Temperature hysteresis

Set open window detection parameters (0.1 accuracy)

Set Force Attach

Possible values:
0 – Deactivate force-attach
1 – Activate force-attach

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Set uplink type

Possible values: 0 (unconfirmed) and 1 (confirmed)

Set Join Retry Period

Value should be in minutes

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Set uplink type

Possible values: 0 (unconfirmed) and 1 (confirmed)

Set Join Retry Period

Value should be in minutes

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Set Child Lock

Possible values: 0 (disabled) and 1 (enabled)

Set temperature range

Set Heating status

Possible values: 0 (disabled) and 1 (enabled)

Set full display refresh period

The allowable full display refresh period range that can be set is (1hour – 24hours). The default value is 10hours

Set delay send target temperature

Set a time delay for sending the target temperature. The allowable delay range that can be set is(0sec. – 255sec). The default value is 10sec.

Set target temperature

The allowable target temperature range that can be set is (5°C – 30°C).

Set automatic heating status mode

In automatic mode, the heating state is on when the target temperature is above the measured temperature.

Set device sensor mode

In sensor mode, the device only displays measurements from available sensors.

Set device deep sleep mode

In deep sleep mode, the consumption of the device is significantly reduced.

Set PIR sensor status

Set the status of the PIR sensor to on or off (1/0).

Set PIR sensor sensitivity

Set the sensitivity of the PIR sensor. The default value is 20.

Set Current temperature visibility

Set a flag to show/hide the current temperature on the display. Default is show (1)

Set Humidity visibility

Set a flag to show/hide the humidity on the display. Default is show (1)

Set Light Intensity Visibility

Set a flag to show/hide the light intensity on the display. The default state is show. (1)

Set PIR init Period

Set the initialization time period of the PIR sensor. Minimum value = 3sec. Default value = 3sec.

Set PIR measurement Period

Set the measurement time period for motion detection by a PIR sensor. Minimum value = 3sec. Default value = 3sec.

Set PIR check Period

It is used to periodically check for motion detected by the PIR sensor. When the period is set to 0, then it is constantly monitored for detected motion. Minimum value = 0sec. Default value = 54sec.

Set PIR blind Period

The blind period is used after motion is detected for how long to disable detection. Minimum value = 15sec. Default value = 10min.

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Led

Behavior - 1-ON, 2-Blink fast, 3-Blink slow, 4-OFF

Set Buzzer

Volume - 0-min... 14-max, 15-OFF

Frequency - 0-1kHz, 1-1.5kHz ... 10-6kHz

Active Time - in seconds, min-1s,"0"- buzzer stay active until command or button is pressed

On Time - in milliseconds, resolution – 10ms

Off Time - in milliseconds, resolution – 10ms

Set Flood Alarm Time

Value should be in seconds. Resolution is 10s

Set Keep Alive

Value should be in minutes

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Open Close Time

Values should be in minutes, range 0-255, cannot be both 0

Set Led

Led Id - 0-Led Open, 1-Led Close, 2-Led Leakage, 3-Led Flood

Behavior - 1-ON, 2-Blink fast, 3-Blink slow, 4-OFF

Set Buzzer

Volume - 0-min... 14-max, 15-OFF

Frequency - 0-1kHz, 1-1.5kHz ... 10-6kHz

Active Time - in seconds, min-1s,"0"- buzzer stay active until command or button is pressed

On Time - in milliseconds, resolution – 10ms

Off Time - in milliseconds, resolution – 10ms

Set Emergency Openings

Maximum allowable value is 15

Set Manual Control

Possible values: 0 (disabled) and 1 (enabled)

Set Keep Alive

Value should be in minutes. Default value is 5

Set Working Voltage

Default value for the device is 1850mV

Enable/Disable device flood sensor

Possible values: 0 (disabled) and 1 (enabled)

Set Join Retry Period

Value should be in minutes

Set flood alarm time

Resolution is 10s. A zero value is forbidden. Default value is 30sec.

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Set Join Retry Period

Value should be in minutes

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Set Target Temperature Step

Value should be in minutes

Keys Lock

Possible values: 0 (disabled) and 1 (enabled)

Set temperature range

Set Join Retry Period

Value should be in minutes

Set uplink type

Possible values: 0 (unconfirmed) and 1 (confirmed)

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Set target temperature

The allowable target temperature range that can be set is (5°C – 30°C).

Set Valve open/close time

Set Full display refresh period

The allowable full display refresh period range that can be set is (1hour – 24hours). The default value is 10hours

Set Current temperature visibility

Set a flag to show/hide the current temperature on the display. Default is show (1)

Set Humidity visibility

Set a flag to show/hide the humidity on the display. Default is show (1)

Set Fan speed

Set Fan speed limit

Set ECM fan min/max voltage

Set ECM fan start up time

Set ECM fan Relay (F-ON) - activated/deactivated

Set Frost protection status - ON/OFF

Set Frost protection threshold and setpoint temperatures

Set Operational mode

Set Allowed operational mode

Set Cooling setpoint not occupied

Set Heating setpoint not occupied

Set Sensor compensation temperature

Set Fan speed not occupied

Set Automatic changeover status - on/off

Set Application - Wiring Diagram

Set Function of digital input/output (OCC)

Set Automatic changeover threshold temperature

Set Device status - on/off

Set Operation after return of power supply

Set Delta temperature 1 (ΔT1)

Set delta temperature 2 (ΔT2) and 3 (ΔT3)

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Set Join Retry Period

Value should be in minutes

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Set uplink type

Possible values: 0 (unconfirmed) and 1 (confirmed)

Set Join Retry Period

Value should be in minutes

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Set CO2 Boundary Levels

"good-medium" - Good-medium CO2 zone boundary value in ppm

"medium-bad" - Medium-bad CO2 zone boundary value in ppm.

Set Auto Zero Value

This value is used by the device for CO2 measurements compensation in order to get 400ppm in fresh air. This value is represented in ppm

Set Auto Zero Period

Auto-zero period in hours. Default auto-zero period, after the factory auto-zeroing, is 192 hours (8 days). During this period the lowest measured CO2 value is accepted as 400ppm and the auto-zero value is obtained automatically. If The period is 0, automatic auto-zero function is disabled, but the obtained or set with command auto-zero value is still used internally.

Set Notify Period

Notification period, in minutes, when measured CO2 is inside the zone. 0 means notify once.

Set Measurement Period

Used until the measured CO2 levels are inside the zone. In minutes.

Set Buzzer Notification

	Beeping (s)	Loud periods (ms)	Silent periods (ms)
Good Zone
Medium Zone
Bad Zone

Set Led Notification

Led Values - 0-None, 1-LED is constantly on for the given time duration, 2-Blink fast for the given time duration, 3-Blink slow for the given time duration.

	Red	Green	Blue	Duration (ms)
Good Zone
Medium Zone
Bad Zone

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here

Downlink Generator

Send command to device to execute (set)

Set Keep Alive

Value should be in minutes

Set uplink type

Possible values: 0 (unconfirmed) and 1 (confirmed)

Set Join Retry Period

Value should be in minutes

Set Watch Dog Params

When no uplink is received for the defined Watch-Dog Period (WDP), the device resets itself.

0 for disabled

"pCU" - Confirmed Uplinks

"pUU" - Unconfirmed Uplinks

Set Child Lock

Possible values: 0 (disabled) and 1 (enabled)

Set temperature range

Set CO2 Boundary Levels

"good-medium" - Good-medium CO2 zone boundary value in ppm

"medium-bad" - Medium-bad CO2 zone boundary value in ppm.

Set Auto Zero Value

This value is used by the device for CO2 measurements compensation in order to get 400ppm in fresh air. This value is represented in ppm

Set Auto Zero Period

Set Measurement Period

Used until the measured CO2 levels are inside the zone. In minutes.

Set full display refresh period

The allowable full display refresh period range that can be set is (1hour – 24hours). The default value is 10hours

Set device deep sleep mode

In deep sleep mode, the consumption of the device is significantly reduced.

Set PIR sensor status

Set the status of the PIR sensor to on or off (1/0).

Set PIR sensor sensitivity

Set the sensitivity of the PIR sensor. The default value is 20.

Set Current temperature visibility

Set a flag to show/hide the current temperature on the display. Default is show (1)

Set Humidity visibility

Set a flag to show/hide the humidity on the display. Default is show (1)

Set Light Intensity Visibility

Set a flag to show/hide the light intensity on the display. The default state is show. (1)

Set PIR init Period

Set the initialization time period of the PIR sensor. Minimum value = 3sec. Default value = 3sec.

Set PIR measurement Period

Set the measurement time period for motion detection by a PIR sensor. Minimum value = 3sec. Default value = 3sec.

Set PIR check Period

Set PIR blind Period

The blind period is used after motion is detected for how long to disable detection. Minimum value = 15sec. Default value = 10min.

Send command to device to receive information (get)

Generated command

Uplink Decoder

Paste your uplink here